Blue Fin 48

Lately I have noticed that two themes have become more constant in my life, one being that I have way less spare time than I used to (and I never had much to start with) and the other being that when my wife and I have the time to go cruising, we enjoy more a cruise “in company” with friends than a cruise where our friends are literally cruising onboard with us. So let me explain the concept to you. Living in the Pacific Northwest, we have amazing cruising grounds literally at our doorstep with smooth, and for the most part, protected waters stretching almost 1,100 miles from our home in Olympia, Washington to Skagway, Alaska. About 900 of those miles are in wonderful wilderness with solitude and beauty surrounding every day spent on the water and every anchorage at night. We have done that cruise several times over the past 20 years, sometimes with guests traveling in the boat with us and sometimes with friends taking their own boats and traveling alongside us. And in retrospect, our favorite trips were the ones with friends traveling alongside doing what I refer to as cruising “in company”. This type of cruising affords all participants a bit more privacy and intimacy than one with a pack of people all on the same boat. There is also a very significant safety factor involved with cruising “in company” because if there is an emergency or the need for a repair, there is a vessel nearby piloted by friends that can help reduce the extra tension involved in an emergency far from help. This safety factor is one that I usually refer to as being a “good boy scout” as you hope that you never need the assistance but it’s there when you need it. It is simply the best preparation for a journey and the best reduction of all the possible fate based factors that may thrust their ugly heads into the realm of a calm and relaxing vacation.

Forgive me for this dialogue but it’s only included to give you a little bit of the mindset for this new design that we are offering up for review. Considering that cruising in company is our preferred way to cruise and that my wife and I don’t really need that much space inside the boat, I started down the path of musing on what would be the most ideal boat for the time and space that my life might allow for cruising in these busy and active times. And so out of that inspiration came the Blue Fin 48, fueled by a very slight influx of dollars from a preliminary design commission by Bill and Meri Roberts, a couple with mostly parallel daydreams as to the perfect cruising boat. Out the door went any consideration about the economics of owning and operating a vessel of a length and breadth that would normally have multiple staterooms and a cost to construct somewhat north of a million dollars and into consideration came what could and would handle a couple for cruising, do it as efficiently as possible at speeds that would cover lots of ground when needed and yet allow unbelievably quiet, smooth and comfortable cruising in anything from 8-16 knots of speed. The only thing that is really extreme about this vessel is that she is basically the layout and the accommodations that you would normally have in a 30-34 ft. boat but is set in a boat that is 48 ft. long. In other words, she will cost certainly more than the typical mid-thirty foot boat, but not as much as her over-muscled brother, and will cruise faster, smoother, and have more space for all the functions of cruising. The downsides to this design are only one; dockage and moorage fees will be the same as the 48-50 ft. skyscraper of a floating condo moored next to you. For my book, I will pay the extra expense for the moorage in exchange of being able to move thru the water at the speed and ease that this vessel would be capable of.

BlueFin48BowSo let’s talk about the design a bit with the first topic being the powering options for her. My first inclination for powering her was a twin diesel arrangement with the engine boxes being set just on the aft side of the rear bulkhead to the cabin. That would allow us to use the top of the engine boxes as seats or tables in the cockpit when entertaining and believe me this cockpit would be a fine entertainment gathering spot for the group of cruisers once the anchors were set firmly and everyone had a quick freshen up after a long day on the water. Picture a pitcher of some refreshing drinks, some background music (not so loud as to drown out conversation) and perhaps some aromatic cigars being lit and puffed on with your friends around you and a whole hectic world left behind. In the twin screw version you will note that I show a couple of really comfortable arm chairs in the cockpit. I really like these folding chairs with their capability of being positioned where I want either out in the sun taking in the last rays of the day’s warmth or under the other half of the covered cockpit out of perhaps a sun too bright or some left over drizzle (remember it rains quite a bit here in the Northwest). It’s always good to have the chance to change one’s seating position and get some fresh air after a long day’s journey and comfortable chairs help with that equation. The other advantage of the twin installation is twofold, the first being the redundancy of power so that if something conspires to leave us with a powering issue, we still have a standby engine that will enable us to continue our journey until we get a chance to fix whatever went haywire on us. The second advantage of a twin installation is the maneuvering advantage that a twin has and with such a long and narrow boat, she will want to go forward far more easily than sideways and the ability of a twin installation to spin the boat either to port or to starboard is rather amazing. Coupled with the bow thruster way up in the nose of the boat, this would be a very easy boat to move about in the close confined waters of a marina or during a docking maneuver. So the twin screw/engine option is a good one and with the main door to the cabin opening into the pilothouse being on the centerline, we can have a nice balanced interior arrangement with the galley on the starboard side, the helm seat just at the forward edge of that space and a “L” shaped dinette on the port side with co/helm on its forward edge.

BlueFin48SternBut it wasn’t long before economy and ease of operation cropped up in my thoughts and I started musing about a single screw version of the same boat. Could it be done on this narrow of a boat without feeling like we are missing or eliminating too much of the useful function of the twin screw configuration? After many hours of cogitating on the problem and trying out the spatial use of the areas that would result, I came across what might really be an even better option to my original twin screw configuration. Looking at the single screw layout, we see the companionway skewed off to the port side of the boat allowing enough room on the centerline for the larger and longer engine box that would be necessary. The galley is set on the port side just forward of that companionway and has a built in co/helm seat at its forward edge, an arrangement we have used successfully in our Surf Scoter and Black Crown designs many times. This may not be quite as compatible for the co/helm but look at the larger “L” shaped dinette area in the pilothouse and as a bonus, aft under the covered part of the cockpit, a mirror image of that dinette aft in the stern area of the boat. Now I can see this version would be an even better socializing cockpit or cabin area with good space to spread out a feast of eats and drinks. For the single screw I would pick the John Deere 4045 diesel which is available in anything from 150-225hp versions and would give us a top speed in the 18 knot range and a cruise speed of 14 knots with 4.4 gallons per hour fuel burn. With about 350 gallons of fuel, that would give this version a range of over 1,000 nautical miles. But slow her down to 8-9 knots and the burn rate lowers to well below 2 gph and the range would improve to well over 1,500 nautical miles. What an efficient and beautiful boat this would be to cruise in!

Soon after working on the single screw version, I started fooling around with a flying bridge version of her. Not being an immediate fan of flying bridges, I changed my tune after assisting in bringing a converted Seine fishing boat back from Alaska to the Puget Sound area many years ago. That boat had a large flying bridge with an unlimited vista and it really was surprisingly warm and dry (even in the wind and rain) with a rain shadow developed by the vertical walls of the flying bridge walls. Trying to steer on that vessel was virtually impossible from the lower helm station with its very small windows and lack of visibility. So after that trip and being “flying bridge enlightened”, this version of the Blue Fin really appeals to me. We can either steer from the lower helm on those heavy weather days or using the flying bridge upper helm in less extreme weather when really wanting maximum visibility.

BlueFin48FlyingBridge

I have a couple of thoughts about the focsle sleeping cabin to make, the first being having enough space to have a proper head and separate shower being one of the advantages of the longer platform of this stretched boat, and the second being the chance of either having single queen sized island berth up forward or with port and starboard single berths with the option to put in a filler between the bunks to make an even larger queen sized berth for when you are cruising with your best first mate. This latter arrangement with its dual function really appeals to me. When going out with some guy friends, we can have port and starboard berths that allow proper separation for personal space and when cruising with my wife, I can put in the filler and sleep with my sweetie with tons of extra room.

The final feature that I want to talk about is the lack of a swim step at the stern of the boat. But you should also notice that her transom folds outward and makes into an integral swim step allowing easy and safe boarding from a dingy or from a stern tie at the dock. But while running at sea, the transom is hinged up to a safe and confining normal configuration. The primary reason why I like this folding transom arrangement is the capability of sliding easily onto and into the cockpit of my 13ft Candlefish skiff. This is a large skiff for this size of mothership but capable of taking us on outings that a normal shorter dingy could not handle. It also allows us to do our cruises with the dingy in the cockpit, keeping the center of gravity and weight low and our flexibility with this design at a real maximum. For those of you that need a conventional transom, this will accomplish that function but for those of you that want a really versatile arrangement in the cockpit, then this configuration will be a real asset.

That’s enough for a really long winded write-up but I am very hopeful to get this design off the drafting table and into the water. Feel free to call me to discuss her merits in detail…. So long for now (till my next design voyage). — Sam Devlin

The Blue Fin 48 is available as study plans and as a custom build by Sam Devlin and his team.

BlueFin48Plan

 

Blue Fin 48 Specifications

Length 48 ft. – 4 in.
Beam 11 ft. – 0 in.
Draft 36 in.
Power Inboard diesel, 150hp – 225hp
Displacement 14800 lbs.
Hull Type Semi-Displacement
Speed 14 knots cruise @4.4gph/18 knots max
Share This:
Facebooktwittergoogle_pluspinterestlinkedin

Josephine 47

A recent visit by friends, Vicky and Craig Johnsen, was highlighted by some elegant drawings that Craig had been working on for a proper power cruiser proposed to be built around a Gardner 6L3 engine he owned. This reminded me of a preliminary design I had worked on some years ago but I must have gotten distracted and had never finished it. Several months later, I dusted off the drawings, wrapped them up and I now present the new version to you here — its resemblance to Craig’s drawing is striking.

I don’t own a Gardner 6L3 (though I certainly wish I did), a 6,700 lb. chunk of sweet sounding metal with a top RPM of 1,000 and generating 150 real horses (not those little ponies so common these days with higher speed and much lighter diesel engines). These horses could swing a 50 inch propeller with ease and make for the maneuvering of the boat armed with such gear a real exhibit of skill and mastery.

But back to the Josephine 47….without owning the Gardner, the next best option is to choose a John Deere 6068 engine with horsepower of 236 medium sized ponies.  This is a reasonable option with a top RPM of 2,400 turns and it should run very smooth at something like a speed of 1,800 revs. That should give us a cruising speed of 8.5 knots over the bottom. The engine is below the pilothouse and very well insulated with Aquadrive isolation of the shaft, soft engine mounts, and lots of sound insulation.

I think the two features that I most like about this design are the extension of the same arrangement that we use on our 81 year old Salmon Troller “Josephine” — the covered afterdeck and the completely separate cabin configuration of the accommodations. With the covered deck aft, the dingy can stow above on the solid roof and canvas drop curtains can be set on the sides of the aft roof enclosing off the entire stern for use when the weather is inclement. You would be surprised at how much you use the ‘covered porch’. Even simple little tasks can be done using the aft cabin housetop as a working and cooking area. When cruising in our own boat, I often wake up early and take a single burner butane stove to the aft deck to brew up my morning coffee without bothering Soitza sleeping below. A pleasant, quiet and peaceful start to the morning is a really great way to cruise. We often don’t do breakfast until we have run for the first hour or two, taking advantage of the typical flat water of the calm summer mornings, and a nice plate of scrambled eggs, salsa, and toast and another cup of coffee seems really civilized while underway. The smell of bacon from the galley in the pilothouse is visceral in its connection with the idea of a pleasant cruise on the water.

If you choose the centerline wheel pilothouse arrangement, there are doors both to port and starboard. The off center helm option shows a different arrangement for the seating in the pilothouse and eliminates the portside door — choose the layout that suits you best.

The fo’c’sle is a separate cabin from the large aft cabin with its own head and shower units. You can condemn the guests you drag along to this cabin where they can stack like cordwood in the staggered over/under port and starboard berths.

So let’s talk briefly about how you might proceed with this design as this drawing is really just a line and lure lowered into the water in an attempt to catch one of you readers. If you find this design tickling your fancy and you would like to talk more about fleshing it out into your own dreams, please give me a call. I look forward to that conversation — it will gives me a feel for what your own ideas are for the perfect boat, enable me to share my own motives and dreams for such a boat, and we’ll both learn a lot in the process. Together, the two of us can come up with a really amazing boat and project! – Sam Devlin

The Josephine 47 is available as study plans and as a custom build from Devlin Boats.

 

Josephine47Side

Josephine 47 Specifications

Length 46 ft. – 8 in.
Beam 13 ft. – 11 in.
Draft 60 in.
Power Inboard diesel, 150hp
Displacement 38900 lbs.
Hull Type Displacement
Share This:
Facebooktwittergoogle_pluspinterestlinkedin

Sockeye 45

Sockeye45CoverThe Sockeye 45 is a full displacement type boat with an almost workboat type appearance. It has enough room inside to be comfortable with two couples. Its draft is modest enough to allow it to cruise in almost any waters you might encounter on the West or the East Coasts.

The profile is straight West Coast Tug type yacht with a heavy portion of fishboat thrown in. With twin masts in a Ketch configuration, this boat would allow a variety of deck boats to be handled on and off the deck.

Sockeye45SamThe Sockeye 45 is powered by a single 145 HP John Deere marine engine is recommended. This engine weighs in at 1,500 pounds and runs at a top speed of 2,400 rpm. The hull itself features a fantail configuration and is very seakindly in the full displacement range of performance. Top speed is 9 knots and cruising speed of 8 knots at about 3 – 4 gallons of fuel per hour. The engine is below the pilothouse and is sound insulated. — Sam Devlin

The Sockeye 45 is available in study and full construction plans, as well as a custom build from Sam Devlin.

 

Sockeye45Interior2Sockeye45profSockeye45Plan

 

Sockeye 45 Specifications

Length 45 ft. – 10 in.
Beam 13 ft. – 2 in.
Draft 55 in.
Power Inboard diesel, 145hp
Displacement 38000 lbs.
Hull Type Displacement
Speed 8.5 knots cruise/9.7 knots max
Range 1500 miles @ 8.5 knots
Fuel Capacity 580 gallons
Water Capacity 80 gallons

 

Share This:
Facebooktwittergoogle_pluspinterestlinkedin

Kokanee 43

For the past 80 years, there has been a type of boat developed in the Northwest called a Halibut Schooner. These boats are evolved from the time when sailing schooners used to be common for commercial cod and Halibut fishing in the waters between Alaska and the mainland US. Those waters were renown for being rough and treacherous and the type of boat that evolved was tough, heavily constructed and extraordinarily seaworthy. The Kokanee is a small, but very able, version of this type and the result is a comfortable boat with good living room in her and a double cabin configuration for cruising with friends when that occasion rises. The main features that I like about this boat are the dinette and galley up in the pilothouse configuration. This allows a fo’c’sle that is very private and with enough space enough to allow the character of the live aboard configuration of this boat to actually be realized. The fo’c’sle has an island double berth, fireplace, lots of locker/stowage room and a dressing vanity. In the evening, this will be a very romantic and cozy cabin to retreat to after the day’s activities, and with its proper lighting and fine woodwork, the cabin will be a favorite retreat. The head is large and has plenty of room for keeping clean and comfortable.

Going up a few steps into the pilothouse, the helm is on the centerline and has a real ship’s wheel. With the dinette and settee to the port side and galley to starboard, everything is right at hand and it will be easy to communicate with crew. At the aft portside corner of the pilothouse, the aft/guest cabin can be accessed and with folding sink and porta-potti, the crew can be comfortable and not have to go forward in the evening to use the fo’c’sle head.

You should note that the cabin roof extends clear to the edge of the boat in the pilothouse area, and with port and starboard sliding doors and with an aft hinged door, all deck areas of the boat can be accessed with ease. The Kokanee is dry stacked for its exhaust and with a slow turning and heavy John Deere diesel engine of 145 horses, it will be quiet and comfortable. I would suggest using a bow thruster on this boat to aid in dockside maneuvering and with a balanced rudder and single screw, the Kokanee will put lots of sea miles below her keel, smoothly and comfortably.

There is plenty of deck space for carrying small rowing skiffs and a proper hard bottomed dingy for exploring an anchorage. This boat will have the capability to cruise to just about any waters that your imagination can take you and will do so with enough crew to be comfortable, safe and handy. I can just see her pulling into some quiet cove in Southeast Alaska, dropping the hook for the evening and after a brisk pull to the shore in the skiff. you can stretch your legs for a few minutes before settling back in for dinner and the evening. Can you imagine a nicer boat to be spending quality time on? Life is indeed too short….Sam Devlin

The Kokanee 43 is available as study plans and as a custom build from Devlin Boats.

Kokanee43PlanKokanee43Profile

Kokanee 43 Specifications

Length 43 ft. – 4 in.
Beam 12 ft. – 4 in.
Draft 58 in.
Power Inboard diesel, 145hp
Displacement 28000 lbs.
Hull Type Displacement

 

Share This:
Facebooktwittergoogle_pluspinterestlinkedin

Golly Wobbler 43

This boat is very much based on the 38 ft. Golly Wobbler that we built a few years ago. The biggest changes have been in the accommodations and in the power package. The goal here is to create a boat that can easily handle two couples cruising with comfort (i.e. built-in berths) and to allow this boat to cruise at speeds in the range of 18 – 20 knots with good fuel economy. Let’s look at the power change first of all and then discuss what spaces opened up as relates to that change.

The primary concern here was to move the engines aft out of the people spaces of the boat and into the stern. Using the concept that we tried successfully on the Topknot 32′, I have moved to a stern drive diesel configuration. I have specified using twin Volvo 41 series stern drives. They have 185 horses each and fit nicely in the stern with a space for generator between and the daybed concept over the top. This will allow some sunbathing room in the cockpit of the boat and should be comfortable when using the cockpit after a days worth of cruising. A barbecue could be run on the daybed platform and with a couple of comfortable deck chairs under the covered cockpit, you can relax out of the weather at the end of the days cruise. The main salon itself has better lounging areas and better communication to the galley area. Note that the bar and refrigerator is opposite the sink and range areas of the galley. There is also a nice skylight over the galley, which gives us enough room for a 9’3″ Guppy sailing dingy over the main salon roof.

Gollywobbler43PlanHelmGoing up a few steps into the pilothouse, you find a chart table and helm area to starboard with a sliding door for access to the fore deck. On the port side, an “L” shaped settee will allow plenty of comfortable seating for the peanut gallery critiquing your navigation. Going below forward into the fo’c’sle, you find the head is to starboard and has enough room for all of its functions, especially at the water closet area. The enclosed shower is through a doorway and has a curtain to keep spray out of the head area proper. Opposite the head area are lockers and a swinging door accessing the guest cabin below the pilothouse proper. There is full 6’2″ headroom below the “L” shaped settee and the large double berth is athwartships with lots of storage room both hanging lockers and drawers. Your guests won’t have any problem staying comfortable here in this cabin with the only small privacy issue being the use of a common head compartment for the two cabins. I’ve provided a slide out pocket door at the front of the head bulkhead which would allow the fo’c’sle cabin to be private to the coming and goings in the head compartment in the day and evening.

I think that this boat would be comfortable with the two couple arrangements and with a cruising speed of 18 knots and fuel consumption of about 10 gallons per hour, should be a fine platform for your West or East Coast wanderings. — Sam Devlin

The Golly Wobbler 43 is available in study plans and as a custom build from Sam Devlin.

Gollywobbler43PlanGollywobbler43Profile

Golly Wobbler 43 Specifications

Length 42 ft. – 8 in.
Beam 12 ft. – 3 in.
Draft 38 in.
Power Inboard diesel, twin 185
Displacement 21000 lbs.
Hull Type Semi-Displacement
Speed 18 knots cruise

 

Share This:
Facebooktwittergoogle_pluspinterestlinkedin

Czarinna 43

This is an elongated version of the Czarinna 35. This version was designed to accommodate a live-aboard couple, or a family for extended cruising. With attention to function, privacy and an open feeling, the Czarinna 43 provides amenities, comfort and stylish character combined with performance and ease of handling. The aft cockpit is large with wrap-around stern decks suitable for seating a crowd for drinks, dinner or cruising. Entering the main salon, the head is to starboard and a separate shower to port. The shower can double as a wet hanging locker in damp conditions. Continuing forward is the dinette with fore-and-aft facing seats to port. To starboard is a fireplace and galley area. The galley is a well-planned design for cooking ease. Forward of the galley are the helm and pilothouse areas with excellent visibility and a comfortable area for helm and co-helm seats. A chart table is located just behind the co-helm.

Sliding companionway doors are accessible from the helm and co-helm seats both to port and starboard. The skipper or crew can go forward from these doors or walk along the decks from the cockpit using the handrails for security. Two steps down from the pilothouse you are in the fo’c’sle, with a comfortable settee berth for a single to port and a large bureau to starboard. A large double berth with twin book and night stand lockers round out the main sleeping area. The entire fo’c’sle area can be closed off with sliding doors for privacy when cruising with several people. The headroom is 6 feet 1 inch in the fo’c’sle, 7 feet in the pilothouse, and 6 feet 6 inch in the main salon.

The Czarinna 43 is long and narrow and, therefore, economically driven. It can weather out most Northwest storms. Power is either a 100 hp single diesel or twin 44 hp diesels, at the owner’s preference. Cruising at 10 knot speeds yields 2-3 gallons of fuel per hour consumption. Tankage for fuel can allow up to 1,000 nautical mile range and water tankage is 250 gallons in twin tanks. The displacement is 19,400 lbs. in full load trim. — Sam Devlin

The Czarinna 43 is available in study plans and as a custom build from Sam Devlin.

Czarinna43TopCzarinna43Side

Czarinna 43 Specifications

Length 42 ft. – 3 in.
Beam 11 ft. – 0 in.
Draft 44 in.
Power Inboard diesel, twin 44hp or single 100hp
Displacement 19400 lbs.
Hull Type Displacement
Speed 10 knots
Range 1000 nautical miles
Share This:
Facebooktwittergoogle_pluspinterestlinkedin

Sockeye 42

Sockeye42Morning2The Sockeye 42 is a full displacement type boat with an almost workboat type appearance, enough room inside to be comfortable with two couples and with modest enough draft to allow it to cruise in almost any waters you might encounter on the West or the East Coasts. The profile is straight West Coast Tug type yacht with a heavy portion of fishboat thrown in. With twin masts in a Ketch configuration, this boat would allow a variety of deck boats to be handled on and off the deck. I have shown her with dry stack exhaust and would recommend a 145 HP John Deere marine engine. This baby weighs in at 1,500 lbs. and runs at a top speed of 2,400 rpm. She is big, heavy, slow turning and would be a good match for this type of hull. The hull itself is of the fantail configuration and would be very seakindly in the full displacement range of performance. Top speed would be 9 knots and cruising speed would be 8 knots at about 3-4 gallons of fuel per hour. The engine is below the pilothouse sole and is sound insulated to result in an interior that is quiet and warm.

Coming into the cabin from the aft cockpit,Sockeye42Interior1 there is a hanging locker to starboard and a bulkhead and door on the port side. This door on the port side gives access to the aft cabin area for your guests. This cabin gives your guests their own area to sleep and rest in when they need the space and with a porta-potti and folding sink, your guests don’t need to go forward into the main head compartment at night. This arrangement could allow any one of the crew to get up in the morning, brew the day’s coffee and enjoy it without bothering the sleep of the rest of the passengers.

The galley is U shaped and allows good room and space for cooking and preparing meals, with good communication to the settee opposite and wood stove for heating your feet on a cool day.

Going up the steps into the pilothouse the helm is on the centerline with an L-shaped settee to port and chart table to starboard. The helm seat should be a swiveling helm seat of fit and construction of the type to allow long watches to be done comfortably.

Sockeye42Morning3

Sockeye42HeadGoing below into the fo’c’sle, the head is to port with the shower compartment being accessed below the seating part of the settee in the pilothouse. Again there is more room at the water closet than in most boats that you might be used to and there should be plenty of room for the crew to be comfortable and private. The double berth is forward to the port side and has a vanity opposite for the fair skinned crew to put their faces on in the morning.

I like this design a lot and think that speed considerations notwithstanding, the Sockeye would be a very handsome, comfortable, and able boat for cruising most any waters with some good friends. — Sam Devlin

The Sockeye 42 is available as a custom build from Sam Devlin.

 

Sockeye42Plan

Sockeye 42 Specifications

Length 42 ft. – 0 in.
Beam 12 ft. – 6 in.
Draft 55 in.
Power Inboard diesel 145hp
Displacement 30000 lbs.
Hull Type Displacement
Share This:
Facebooktwittergoogle_pluspinterestlinkedin

Oysta 42

Oysta42SideA problem many boaters have is the unequal interests of their spouses in their real or imagined cruising adventures and, most specifically in “sailing” cruising adventures. Along came an East Coast customer who wished to spend the second half of his life with his wife continuing as his partner. It’s always a ticklish design issue, attempting to make a boat comfortable and unique enough to hold the interest of a less-than-eager spouse, yet capable and challenging enough to hold the interest and enthusiasm of the more experienced partner.

The Oysta 42 was specified to be a “motor sailer.” And not just a sailboat with an auxiliary engine. The Oysta 42 is a true 50/50 motor sailer capable of motoring through any sea condition; with the sail-assist it’s capable of doubling its useful cruising range from 1500 miles under power alone to better-than-3,000 miles with sail. And keeping an engine running affords a lot of comfort and luxury on board, while sail alone might work against the less willing crew member’s enthusiasm. An inboard low aspect ratio ketch rig was chosen to work within the design framework. Both masts are on tabernacles so that the rig can be easily lowered for canal passages. The aft pilot house design was selected allowing a large shaded (with boom canvas) outside deck area for carefree warm weather anchorages.

Oysta42RenderLooking at the accommodations, one can see a large, forward master cabin as a private refuge. The head is clear up in the bows of the boat with a separate shower and enough room to dress in leisurely comfort. There are bureaus and hanging lockers for clothing and stowage for a long cruise, and a reading seat to allow some private moments away from other crew members. Just aft of the master’s cabin is a separate cabin with its own access from a large 3 x 3′ deck hatch (which also functions as a mid-deck table). With port and starboard berths, this cabin functions as a crew’s quarters or the guest cabin for visiting family members or friends. Access to the large engine room is through the aft bulkhead of the guest cabin.

Power can be either twin small diesels of 50 hp each, or with one large single diesel of 100-120 hp. My own choice would be twin 4 cylinder 50 hp diesels as the maneuvering edge gained by twin engine installation more than justifies the small additional cost. And while motor-sailing, the lee sided engine can be left running which helps keep the shipboard electrics in shape.

In effect, the two diesels function like a built-in generator providing 12 volt and 110 AC power through high-output alternators and generous battery bank storage capabilities. Fuel tankage allows a range of 1,500 nautical miles under power alone.

Moving aft past the large mid cockpit, the pilot house is entered through port and starboard sliding doors, and features a centerline mounted helm with inside-or-outside steering, chart table to starboard, galley to port, and a real bridge to work the boat from. Stepping aft and down is a huge settee with a large table and enough room to accommodate 6 adults. A small head is off to port for quick access from the pilothouse and salon.

With tabernacle rigs, a displacement of 24,000 lbs., modest draft of 5’0″ and room enough for a long cruise, I can just imagine leaving the snow behind for warm Caribbean winds, with good ripe local fruit and pungent island rum – and best of all with my favorite mate to enthusiastically share my adventure. — Sam Devlin

The Oysta 42 is available in study plans and as a custom build from Sam Devlin and his crack crew.

Oysta42Top

Oysta 42 Specifications

Length 42 ft. – 1 in.
Beam 12 ft. – 1 in.
Draft 60 in.
Power Inboard diesel, twin 50hp or single 100-150hp
Displacement 28000 lbs.
Hull Type Displacement
Sail Area 481 sq. ft.
Share This:
Facebooktwittergoogle_pluspinterestlinkedin

Josephine 40

Josephine40shortmast

 

In extensively cruising my 1934 salmon troller Josephine, I’ve come to appreciate many of her qualities. She’s a strong boat, comfortable in a rolling sea, and graceful in a classic workboat sense. Owning a stitch and glue boat business, it was only natural for me to take what I felt are the best parts of Josephine and adapt them to my method of boatbuilding. The result is a boat with all the aesthetic appeal of the original with the added benefits of increased interior room and decreased boat weight. The result is the Josephine 40.

It would do little good to belabor the various layouts in writing as the study plans will do a far better job. Submitted to you, dear reader and future Captain, are a number of idea drawings ranging from a working salmon fishing troller/fishboat to a motorsailor to a flybridge expedition yacht. Of course, the Josephine 40 can be built to whatever reasonable configuration the owner chooses. Give the shop a call so we can set up a time to talk about the particulars. The waters are waiting for you. – Sam Devlin

The Josephine 40 is an extensive design. The study plans are available to help you get a handle on the many options.

Josephine 40 Specifications

Length 40 ft. – 9 in.
Beam 12 ft. – 3 in.
Draft 53 in.
Power Inboard diesel
Displacement 28000 lbs. – 42000 lbs. (Full fishhold)
Hull Type Displacement
Share This:
Facebooktwittergoogle_pluspinterestlinkedin

Hope of Glory

The Hope Of Glory is another of our fantailed stern hulls with a lovely balance to her lines and a ketch rig for proper and easy sail handling by a short-handed crew.

HoGop

Hope and Glory Specifications

Length 38 ft. – 4 in.
Beam 12 ft. – 0 in.
Draft 52 in.
Power Inboard diesel 15hp
Displacement 22400 lbs.
Hull Type Displacement
Share This:
Facebooktwittergoogle_pluspinterestlinkedin